I bought my first block plane because an older carpenter I worked for got tired of watching me sand a chamfer by hand. That was on a barn sill in New Hampshire, and I used that plane more in one week than I had used a sanding block all year. The one living on my bench now is the Jorgensen No.60-1/2, a low angle block plane I have been picking up daily for a couple of years. It is not the fanciest plane I own. It is the one I reach for.
If you are coming back to hand tools after a long break, or buying your first plane that is not a garage sale find, a block plane is where I would start. It is small. It weighs 1.5 pounds. It carries a 1.38 inch iron, narrow enough to work inside a drawer and wide enough to true the edge of a small panel. You hold it in one hand and the other hand holds the work. That single fact explains most of what follows.
The plane I pick up more than any other in the shop
Jorgensen No.60-1/2 Low Angle Block Plane. 1.38 inch O1 tool steel iron, cast iron base, 1.5 pounds. Small enough to keep in an apron pocket and use forty times a day.
Amazon See the No.60-1/2 on Amazon →It rides in your apron pocket instead of sitting in a drawer
Most planes live on a shelf and come out for a job. A block plane travels. At 1.5 pounds with a 1.38 inch iron it goes in the apron pocket and comes back out forty times in an afternoon: once for a chamfer, once to ease a scribe line, once to clean up a corner that caught your sleeve. The tool you carry is the tool you use. The tool in the drawer is a tool you own.
Breaks a sharp edge in two passes, not twenty minutes of sanding
A chamfer on a table leg is four passes with a block plane and a half hour with sandpaper, and the plane leaves the crisper line. I set the cutting depth shallow with the knob, start at the far end of the leg so I do not blow out the corner, and work back toward myself. Two passes gives me a chamfer about the width of a pencil line. If you build stools or chairs, this is the plane that keeps an edge from feeling sharp against a hand.
Trims end grain clean where other planes tear it
End grain is where most planes embarrass themselves. A low angle plane sets the iron at a shallower angle to the sole, so it slices the fibers instead of scraping across them. That is geometry, not advertising, and it is why a low angle block plane is the tool people hand you when a crosscut needs cleaning up. Take a light cut with a sharp iron and you get a polished face on the end of a rail. A dull iron and a heavy cut will tear it like anything else.
Fixes a sticking door without pulling the hinges
A neighbor called me in July about a door that had swollen shut in an old house. Painted shut a dozen times over the years, and no interest in taking the door off. I took the latch edge down a hair with a block plane, in place, working from the middle of the edge outward so I would not split the paint at the corners. Fifteen minutes and the door latched. That is not fine furniture work. It is the work that keeps a small plane in the pocket of a carpenter who stops by to help.
One knob sets the cut, so there is nothing to fiddle with
The cutting depth is adjustable by turning the knob, and that is the adjustment I touch most during a session. Take a light cut, look at the shaving, turn a little, take another. After a while you set it by the sound of the cut instead of by eye. I do not want to be counting screw turns while I balance a door on my knee. I want one thing to turn and a shaving thin enough to read a newspaper through.
The O1 iron sharpens in a minute and comes back fast
The Jorgensen blade is O1 tool steel, a simple carbon steel that takes a fine edge on water stones and gives it up gracefully. My sharpening station sits by the window in the shop, and a block plane iron is small enough that touching it up mid-project takes about a minute, not an evening. O1 will not hold an edge like the hard alloys if you are planing teak all day. For a Saturday of pine and cherry it is plenty, and it comes back quickly.
Reaches the rub that a No. 4 cannot get near
The iron is 1.38 inches wide, and that number matters more than it sounds. It fits inside a drawer side, between a drawer bottom and its runner, along the inside of a small box after glue-up. A No. 4 is twice the plane and will not go there. When a drawer rubs on one corner, the block plane reaches the rub and the bigger plane reaches the drawer front and stops. Small boxes and drawers are most of what I build now, and most of what gets fitted afterward.
The cast iron base and flat bottom keep the cut honest
The body is cast iron with a polished flat bottom, and a flat sole is the whole game with any plane. If the sole rocks, the cut rocks with it. Mine has stayed flat through two years of steady use, and I check it once a season against a straightedge on the bench. At 1.5 pounds it is heavy enough to carry through a cut on its own and light enough that your wrist is not worn out by four in the afternoon.
Teaches you to read grain faster than any book will
You cannot learn grain direction from a book. You learn it by planing a board the wrong way and watching the surface lift into fuzz. A piece of maple with reversing grain will teach you in an afternoon what a chapter cannot. Take a light pass, watch the shaving, and if the surface starts to tear, turn the plane around and come from the other end. A block plane is small enough that turning it costs nothing, which is exactly why it makes a good teacher.
Does most of the actual plane work on a Saturday project
If I add up the planing I do in a year, most of it is small. Easing an edge, trimming a plug flush, fitting a drawer, cleaning up a tenon shoulder, taking a whisker off a lid that will not seat. The Jorgensen No.60-1/2 does that work without ceremony. It stays out on the bench instead of going back in the till, and it is the plane I would replace first if it ever walked off.
What I'd Skip
I would skip using a block plane for anything long. It is not a jointer and it will not flatten a panel, because the sole is short and it follows every dip in the board. For an edge that has to be straight over three feet, use a No. 7 or a power jointer and save yourself the argument. I would also skip buying three specialty planes before you can sharpen one iron well, and skip the aftermarket blade until the stock one has taught you what a truly sharp edge feels like. And I would skip the notion that you need a second block plane at a different angle before you have worn out the first.
A 1.38 inch iron is the reason this plane fits inside a drawer and a No. 4 does not. No amount of technique changes that.
The plane that stays out on the bench instead of going back in the till
Low angle, 1.38 inch O1 tool steel iron, cast iron base with a polished flat bottom, 1.5 pounds. If you are rebuilding a hand tool kit one piece at a time, this is a sensible addition after a good square and a decent saw.
Amazon See the Jorgensen No.60-1/2 on Amazon →